Overview:
The AUDIX ADX12 is a professional miniature gooseneck condenser
microphone designed for applications such as podium, presentation, meetings and
teleconferencing.
- With a uniformly controlled cardioid polar pattern, the
ADX12 helps isolate the speaker from ambient noise.
- The ADX12 is available in a
hypercardioid polar pattern fortighter pick-up control. (model ADX12HC)
- The ADX12 is desiged with an integrated preamp circuitry
built into the base of the XLR. They can be mounted permanently via the
supplied flange mount or with an optional base with an internal shock mount
(see model ATS10, ATS1, ATS1L). The mic may also be used on a standard mic
stand using the DCLIP snap to fit mic holder.
- The ADX12 operates on phantom power of 18 - 52 V.
Features:
- Natural accurate sound
- Interchangeable capsule
- Low profile design
- Dual gooseneck sections allows for precise positioning
- Low noise electronics
- Available with cardioid or hypercardioid polar pattern
Applications:
- Pulpit, podium
- Board meetings, teleconferencing
- Video, recording
- Room security or monitoring
What's in the Box?
- Flange table mount (TM1218)
- External foam windscreen (WS1218)
Optional Accessories
- ATS1 - Table Base with programmable on/off switch
- ATS1-LOGIC - Same as above, with Logic
- ATS10 - Table Base with on/off switch
- SMT1218R - Rubber insulated shockmount
- DCLIP - Mic stand adapter
- APS 2 - Two-channel phantom power supply
Microphone Characteristics:
User Tips:
- Speaking distance and angle of microphone: The two flexible
portions of the microphone will enable you to position the mic according to height and speaking style of
the user. In general, the microphone can be angled at 60-75 degrees towards the speaker and be 12-16 inches away
from the mouth. A shorter distance can be used for a fuller sound or for weaker voices, but avoid getting
too close to the microphone element.
- Windscreen: The supplied windscreen should be used to help
minimize pop noise and breath noise. If breath or pop noise appears to be excessive, either move further away
from the microphone or try speaker over the top of the microphone rather than directly into it.
- Using with Table Stand: For ultimate flexibility and
portability, the optional ATS1, ATS1 LOGIC or the ATS 10 heavy duty table stands are available. Since the electronics
for the ADX12/18 are built right into the base of the microphone, all that is necessary is to plug the mic
directly into the table stand connector on the top of the base. The mic cable will be plugged into the back of the base and
connected to a low impedance mic level input on the mixer or recording device. Remember that phantom power is
required in order to operate. There is a noiseless 2 position on-off switch located in the table stand. The
down position is ‘on’ and the up position is ‘off’. The LED indicator light will be lit when the mic is turned on. This
is not a push-to-talk system so you need not hold down the switch, just push and click to on or off position. A
standard XLR-XLR microphone cable can be used to connect the ATS 10 to the mixer or recording device.
- To use on microphone stand: The ADX12/18 may be used on any
standard microphone stand by using the D-Clip. The XLR base of the microphone will snap securely
into the D-Clip and can be used at any angle
Dimensions:
Specifications:
- Transducer Type...................... Pre-Polarized Condenser
- Frequency Response............... 40
Hz - 18 kHz
- Polar Pattern ...............Cardioid
- Output Impedance ...............150
Ohms balanced
- Sensitivity............. 25 mV /
Pa @ 1k
- Equivalent Noise
Level........... 28 dB (A weighted)
- Signal to Noise Ratio .............66 dB
- Power Requirements ...............18
- 52 Volts phantom
- Maximum SPL ................≥120 dB
- Cable/Connector ....................3 pin
gold plated male XLR connector
- Polarity .................Positive
pressure on diaphragm produces positive voltage on
pin 2 relative to pin 3
- Housing/Finish............... Machined Auminum and Brass / Black matte
- Weight ................113 g / 4
ounces
- Length ....................403 mm / 16
inches