Overview:
The Warwick BC300 combo offers 300W of useable power, and
has great, useful features for the stage, studio or bedroom.Classic sound with modern performance.
- Manufacturing
techniques and component quality has improved drastically over the last couple
of decades
- Noise and hum are no longer unavoidable side effects of great
sound
- So here we have recreated the "Classic" 10 band graphic EQ
powered Bass Amp with big, powerful, tight sound in a modern package.
Features:
CLASS-A CIRCUITRY
- Class-A amplifiers are typically more linear and, as such,
are less complex than other amplifier classes. The amplifying element is biased
so the device is always conducting to some extent. This means the amplifier is
always on, avoiding the problem of crossover distortion associated
with class-AB and -B designs.
Low-Z CIRCUITRY
- By lowering the impedance inside an electronic circuit you
lower the amount of thermal noise. In an amp where you have tone controls that
lift mids and highs a considerable amount, proper impedance level makes the
difference between enduring audible annoying hiss, and enjoying a pleasant
tonal experience.
DYNAMIC DISTORTION LIMITER (TM)
- Distortion occurs when an amplifier works beyond its range,
when the power supply cannot supply the power any more to take the amp higher.
A common method to control distortion in amps is to use a limiter, a device
that stops the signal going beyond a specific level. Audio limiters work by
setting a threshold signal level where the circuit kicks in and keeps signal
levels within the capabilities of the power supply. This method is not very
precise and often causes audible effects such as pumping and thumps. We
designed a circuit that instead reads the distortion level in the power amp and
starts limiting as soon as the amp shows even miniscule amounts of distortion.
This means our amps always stay within 0.3% distortion (THD) when most amps are
rated at between 5-10% distortion (that means that to get your 300 Watts out of
a 300 Watt amp you will get it audibly distorted and if you want a clean signal
the power will be a lot less). There are desirable types of distortion, but
these are not usually associated with transistor amplifiers, but more commonly
associated with tube amps and effect pedals. Warwick%u2019s goal is to give the
user a great, clean sound allowing the user to decide how much, and what kind
of distortion to employ.
INTEGRATED SPEAKER DESIGN
- All the speaker drivers and cabinets have been
designed in tandem with the electronics to create units that work together
efficiently . Careful consideration has been taken to modify all parameters,
thereby achieving the best results in sound and performance. All components
reflect a custom designed solution to give the end user optimum control over
his/her tone, volume and configuration
Front Panel Features:
- ACTIVE – Input to plug in shielded guitar cable. This input
is low sensitivity to suit the output from guitars with active electronics.
- PASSIVE – Input to plug in shielded guitar cable. This input
is high sensitivity to suit the output from passiveguitars.
- GAIN – Controls the input signal level to the preamp.
- COMPRESSION – Controls the amount of compression applied to
the signal.
- MUTE – Switch mutes all outputs, except the tuner out and
the headphone out. LED is provided next to this switch to indicate when the amplifier is muted.
- COMPRESSION IN/OUT – Switches the compressor circuit in and
out of the signal path.
- EQUALIZER – 10-band graphic equalizer section. Sliders
control +/- 12dB of gain at the frequency indicated below each control..
- EQ IN/OUT – Switches the EQ circuit in and out of the signal
path
- BASS – Shelving Bass Control gives +/- 18 dB gain at 60 Hz.
- TREBLE – Shelving Treble Control gives +/- 18 dB gain at 10
Hz.
- VOLUME – Controls the main output volume. Adjust this for
your preferred overall playing volume.
- AUX IN – Input to connect external sound source. This can be
used for plugging a CD, tape or MP3 player into the amp for practicing, rehearsing or for
connecting a second preamp into the system.
- HEADPHONE – Output for connecting a headphone. Dedicated
stereo headphone amp. It is recommended to mute the amp when using headphones
Rear Panel Features:
- POWER – On/off switch for main power. For your safety
remember to connect power cord to the amplifier first, then to the AC outlet and then turn this switch on.
It works backwards when you want disconnect unit – firstly turn switch off, then disconnect
cord from the AC outlet and finally disconnect cord from amplifier.
- MAINS IN AC – AC terminal with integrated fuse compartment
for connection to the mains power supply. To exchange the fuse you have to disconnect power cord first
and use small screwdriver to remove fuse carrier. Use only the same size and type for
replacement. Using a fuse with a different rating than specified can cause damage to your amplifier.
- TUNER OUT – Dedicated output for tuners. Signal remains
active in this output even when amplifier is muted which allows for “silent tuning”.
- SEND & RETURN – Insert point for external effects unit.
To use effects loop connect the send socket to the input of the effects unit and the output of the effects unit to
the RETURN socket. The effects loop is of the serial type.
- LINE OUT – Unbalanced output to external devises (auxiliary
power amplifier, mixing console etc.).
- DI OUT – Balanced XLR output to external devices such as PA
and studio mixing consoles.
- PRE-POST – switch to control the DI OUT. In PRE position the
signal at DI OUT is the signal without any compression or equalization. In POST position signal at DI
OUT is fed after the compressor, tone controls and effects loop.
- GROUND LIFT – Switch to lift the chassis ground connection
from the DI output. Helps to prevent hum caused by ground loops.
- SPEAKER OUT – Output combo connectors (¼” jack and lockable
coaxial) for connecting speakers. These are connected in parallel. Connect only speaker combinations
with a summary load equal or greater than 4Ω
Specifications:
- Bass combo
- 300 Watt Power Amp
- 15" Warwick Custom Speaker
- 4" High frequency horn
- Bass reflex Housing
- Rugged metal grill
- Class A Low Noise Preamp
- 2 Way EQ with controls for bass and treble
- 10 Way graphic Equalizer, switchable Mute Switch
- Adjustable, switchable compressor
- Temperature-dependent fan
- 2 Inputs for active or passive Basses
- The two instrument inputs are suitable for 2 instruments at
the same time
- Line Output with Ground Lift switch
- Balanced DI output with switch Pre / Post EQ
- FX Loop
- Tuner Output
- Aux Stereo-Input, Mini jack for connecting MP3 player, CD
player etc.
- Integrated headphone amplifier. Aux in stereo signals over
headphones in stereo
- Speaker out connection for additional speaker Cabinet
- Dimensions: (B/H/D) 530mm x 580mm x 430mm / 21" x
23" x 17"