PLEASE SELECT THE DESTINATION COUNTRY AND LANGUAGE :
Price | |
---|---|
Discounted Price | Php 69,000.00 |
Discounted Amount | Total Discounted Amount KRW (Mobile Purchase Discount KRW ) |
Reward Points |
Points :690.00(1.00%) KRW % KRW % KRW % KRW % KRW % KRW % KRW % KRW % KRW % |
Shipping Method | Selected by customer |
Shipping Cost | International Shipping Fee |
Description |
Shipping | |
---|---|
Quantity |
Product Info | Product | Remove |
---|---|---|
Total(Qty) 0 |
Overview:
IPS Series is a range of two-way professional amplifiers that combines high quality performance and reliability with the latest power amplifications technologies.
Features:
Applications:
1.) POWER switch - Push to turn on / off the amplifier. Before switching the amplifier on, check all cables and turn fully counterclockwise both channel level controls 3 .
2.) POWER LED - When lit, the amplifier is switched on.
3.) Control (one per channel) to adjust the output level of the respective amplifier channel. Turn clockwise to increase the output level (0 dB = max. level), turn counterclockwise to decrease. If the amplifier is set to BRIDGE mode, use the channel 1 control only.
4.) FAULT LED (one per channel) - When lit, it indicates the internal protection intervention (due to overload, short-circuit, thermal drift, fault) and the respective channel is muted .As soon as the problem is solved, this LED will be dark. When turning the amplifier on, this LED stays lit for three seconds
5.) CLIP LED (one per channel) - It blinks when the signal level reaches the clipping point, causing the limiter intervention of the respective channel. If it stays lit continuously, the input signal level is excessive.
6.) SIGNAL LED (one per channel) - When lit, it indicates the signal presence (above –40 dBu) at the respective input.
Rear Panel Features:
7.) CH1 INPUT - Channel 1 balanced audio input (female XLR connector).
8.) CH1 LINK - Channel 1 balanced parallel audio output (male XLR connector). This output is linked in parallel with the channel 1 input and is useful to link another amplifier.
9.) CH2 INPUT (STEREO MODE ONLY) - Channel 2 balanced audio input (female XLR connector).
10.) CH2 LINK - Channel 2 balanced parallel audio output (male XLR connector). This output is linked in parallel with the channel 2 input and is useful to link another amplifier.
11.) MODE switch - Before turning the amplifier on, set the amplifier mode selector to the right position among BRIDGE, PARALLEL (mono) and STEREO.
12.) SENSITIVITY switch - Set the sensitivity switch to either 0.775 V or 1.4 V, which is input signal voltage required to get the maximum power output from the amplifier.
13.) CH 1 OUTPUT - Channel 1 output to loudspeakers (SPEAKON connector). If the amplifier is set to BRIDGE mode, only connect this output
14.) CH 2 OUTPUT - Channel 2 output to loudspeakers (SPEAKON connector). Do not use this output if the amplifier is set to BRIDGE mode.
15.) Power cord input. - Connect the power cord only to a mains socket outlet with a protective earthing connection.
16.) RESET push-button - Push this button to (try to) reset the amplifier when is muted due to the thermal protection.
Operation Modes:
Make sure the amplifier is switched off before setting the MODE switch to STEREO. In stereo mode, both channels operate independently and each front panel level control affects its respective output. Minimum load impedance is 4 Ω per output. Loudspeakers shall be connected to the outputs 1 (left channel) and 2 (right channel).
Make sure the amplifier is switched off before setting the MODE switch to PARALLEL. In mono mode, both channels are linked to input 1 (therefore receiving the same signal). Each front panel level control affects its respective output, allowing you to set (if necessary) different levels. Minimum load impedance is 4 Ω per output. Loudspeakers shall be connected to the outputs 1 and 2.
Note that only the amplifier inputs are linked in parallel. This is NOT an output parallel mode. Never connect both outputs in parallel!
Make sure the amplifier is switched off before setting the MODE switch 11 to BRIDGE. In ‘bridge’ (mono) mode, both amplifier channels work with the same input signal, but with inverse phases. The result is a doubling of the output voltage in order to get a double power (on a double impedance load).
Connect the CH 1 input and output only.
The output level is adjusted only by the channel 1 front panel control. Pay attention to the output SPEAKON wiring: pin 1+ positive, pin 2+ negative.
Minimum load impedance is: 8 Ω.
INPUT SECTION
OUTPUT SECTION
SYSTEM PARAMETERS
POWER REQUIREMENTS
PHYSICAL SPECIFICATIONS
Product Name | IPS 3700 |
---|---|
Brand | RCF |
Sale Price | Php 69,000.00 |
Mileage | Points :690.00 |
수량 | |
Product Code | P0000TKC |
Product Details | Power Amplifier (1,500W) |
QR Code |
The Eight Basic Consumer Rights : http://www.dti.gov.ph/dti/index.php?p=720