Front Panel Features:

1.) POWER INDICATOR - Lights up in green while the subwoofer is on.Lights up in red while the subwoofer is set in the standby mode by the operation of the automatiic power switching function.Goes of when the subwoofer is set in the standby mode

2.) STANDBY/ON BUTTON - Press this button to turn on the power when the POWER switch is set in the ON position. (The power indicator lights up in green). Press again to set the subwoofer in the standby mode (The power indicator goes off)

3.) B.A.S.S (Bass Action Selector System) - When this button is pressed in to the MUSIC position, the bass sound in audio software is well reproduced. By pressing the button again so that it pops out at the MOVIE position, the bass sound in video software is well reproduced.

4.) HIGH CUT CONTROL - Adjusts the high frequency cut off point. Frequencies higher than the frequency selected by this control are all cut off (and no output)

5.) VOLUME CONTROL - Adjusts the volume level. Turn the control clockwise to increase the volume and counterclockwise to decrease the volume

Rear Panel Features:

6.) VOLTAGE SELECTOR SWITCH - If the preset setting of the switch is incorrect ,set the switch to the proper voltage (110V,120V,220Vor 240V) of your area.

7.) POWER SWITCH - Normally, set this switch to the ON position to use the subwoofer . In this state, you can turn on the subwoofer or turn the subwoofer into the standby mode by pressing the STANDBY/ON button. Set this switch to the OFF position to completely cut off the subwoofers power supply from the AC line.

8.) OUTPUT (TO SPEAKERS) TERMINALS - Can be used for connecting to the main speakers. Signals from the INPUT1 terminals are sent to these terminals.

9.) INPUT1 (FROM AMPLIFIER) TERMINALS - Used to connect the subwoofer with the speaker terminals of the amplifier.

10.) INPUT2 TERMINALS - Used to input line level signals from the amplifier

11.) AUTO STANDBY (HIGH/LOW/OFF) SWITCH - This switch is originally set to the OFF position. By setting this switch to the HIGH or LOW position, the subwoofers automatic power-switching function operates.

12.) PHASE SWITCH - Normally this switch is to be set to the REV (reverse) position.

Connecting to Line Output (pin jack) terminals of the amplifier

• To connect with a YAMAHA DSP amplifier (or AV receiver, connect the SUBWOOFER (or LOW PASS etc) terminal on the rear of the DSP amplifier (or AV receiver) to the L/MONO INPUT2 terminal of the subwoofer.
• When connecting the subwoofer to the SPLIT SUBWOOFER terminals on the rear of the DSP amplifier , be sure to connect the L/MONO INPUT2 terminal on the "L" and the R INPUT2 terminal to the "R" side of the SPLIT SUBWOOFER terminals

Using One Subwoofer :

Using Two Subwoofers :

Connecting to speaker output terminals of the amplifier

If your amplifier has two sets of main speaker output terminals and both terminals can output sound signals simultaneously

• Connect one set of main speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer and connect the other set of main speaker output terminals of the amplifier to the main speakers
• Set the amplifier so that both sets of main speaker output terminals output sound signals simultaneously

Using one Subwoofer (with speaker cables)

Using Two Subwoofer (with speaker cables)

If your amplifier has only one set of main speaker output terminals

Connect the speaker output terminals of the amplifier to the INPUT 1 terminals of the subwoofer and connect the OUTPUT terminals of the subwoofer to the main speakers

Using one Subwoofer (with speaker cables)

Using Two Subwoofer (with speaker cables)

Specifications:

• Type: Advanced Yamaha Active Servo Technology
• Driver: 20cm (8") cone woofer Magnetic shielding type
• Amplifier Output (100 Hz, 5 ohmns, 10% THD) : 150W
• Frequency Response : 28 Hz-200 Hz (-10 dB)
• Power Consumption : 95W
• Standby Power Consumption: 0.5W
• Dimensions (WxHxD) : 290mm X 360mm X 322mm ( 11-7/16" x  14-3/16" x 12-11/16")
• Weight: 11.5kg (25 lbs. 60 oz.)
• Color: Black