The PLM 10000Q is available with either binding posts or an
“embedded patch panel” with Neutrik Speakon connectors (2 x NLT4 and 1 x NLT8). Common connectors include; 2 x analog input XLR
with switchable Iso-Float, 2 channels of AES/EBU with link-through capability for daisy chaining, 2 x EtherCon® for linking or redundancy.
A 32 amp PowerCon® connector is used for mains supply
Front Panel Features:
The front panel is the “local control center” for the PLM
10000Q. An intuitive, menu driven interface allows quick access to key
functions using the moisture resistant silicone touchpad. Information
is clearly displayed on the daylight-readable, 2.5-inch LCD panel. The
soft-button keypad and precision rotary encoder provide control of
processing and amplification functions, with key lock available.
- 1.) Standby power toggles the frame between Standby and On modes
- 2.) Eight "soft "buttons allow sub-branches and parameters (shown in the display ) in the menu system to be selected when in Menu Mode
- 3.) Module "ME" Buttons. In meter mode these two multifunction selection and indication buttons access processing modules A and B respectively.
- 4.) In meter mode these four "soft " multifunction selection and indication buttons identify, monitor and control output channels. Order is dependent on module routing
- 5.) ID LED indicates communication between the modules in the PLM and the Lake Controller Software
- 6.) Rotary encoder is used to edit parameters in the menu system. The ring around the encoder lights up when the encoder has functionality
- 7.) Exit Button provides escape functions in both Menu and meter view navigation
- 8.) Display . High brightness monochrome 128x128 pixels
- 9.) Menu accesses Frame control utilizing a menu-driven navigation interface. The buttons around the display and the exit button are used for control and selection options in the menu
- 10.) Meter toggles through Home,Module and Temperature Meter views
- 11.) Mute Enable allows module inputs and output channels to be muted. Flashes when mute enabled . Can be disengaged manually.
Rear Panel Features:
Specifications:
General
- Number of input channels...............................2
- Number of output channels............................4
- Peak total output all channels driven .............10800 W
- Peak output voltage per channel................... 153 V
- Max output current per channel .................... 49 A peak
Max output power all channels driven
- 16 ohms................... 660
W
- 8 ohms.....................1300 W
- 4 ohms..................... 2300 W
- 2 ohms 1.................. 2350
W
Max output power bridged
- 8 ohms .................4600 W
- 4 ohms ................4700 W
Performance
- THD + N 20 Hz - 20 kHz for 1 W...................................................< 0.05 %
- THD + N at 1 kHz and 1 dB below clipping..................................... < 0.04 %
- Dynamic range with analog inputs ..................................................>112 dB
- Frequency response (1 W into 8 Ohm, 20 Hz - 20kHz).....................+/- 0.05 dB
- Common Mode Rejection (CMR) ....................................................>74
dB, 20 Hz to 20 kHz
- Internal Sample Rate / Data path....................................................96 kHz / 32 bit floating point
- Product propagation delay (straight path analog server input
-> amp).............1.61 ms
- Product propagation delay AES 96 kHz / analog input ..................................1.68 ms
Sample Rate Converters
- THD + Noise ............................0.00003
%, 20 Hz - 20 kHz, unweighted
Analog to Digital inputs
- Inputs....................................................2 inputs x 2
link
- Input sensitivity settings ...........................+12
or +26 dBu
- THD + Noise ................................ 0.00022
%, typical at 1 kHz unweighted at +26 dBu headroom setting
- THD + Noise ...............................0.00033
%, typical at 20 Hz and 20 kHz unweighted at +26 dBu headroom setting
Gain, Sensitivity and Limiters
- Adjustable Inter-Sample Voltage Peak Limiter (ISVPL)...............17.8 - 153 V, step size 0.1 V
- Current Average Limiter (CAL) > 300 ms .................................25 Arms
- MaxRMS (rms voltage limiter) ................................................Yes
- MaxPeak (peak voltage limiter)............................................... Yes
- Output attenuator.................................................................-Inf
to 0 dB, step size 0.25 dB
AES3/EBU (sample rate converters available as desired)
- Supported sample rates...................... 48,
96 kHz
- Support redundant paths...................... Yes
- Flexible topology.................................. yes
- Network latency...................................0.8,
1.3 and 4 ms
Back panel Interface
- AES / EBU / I/O (input + link).........................2 x 3-pin XLR
- Analog, 2-channel I/O (input + link)................. 4 x 3-pin XLR, electronically balanced
- Output connectors........................................Neutrik
speakON (1 x NLT8, 2 x NLT4) or 4 Binding Posts (pairs)
- Auto 10/100, Auto Uplink..............................2
x RJ45 etherCON
- Control and monitoring interface......................Via Ethernet for Lake Controller software, or DLM (the
3rd party protocol)
- Detachable mains cord .......................................Neutrik
PowerCon rated at 250V/32A
- Cooling ................................................Two fans,
front-rear airflow, temperature controlled speed
Front-panel user interface
- Display ................................................ 2.5 inch,
daylight readable LCD
- Fault/Warning/Limit/Clip indicators ..........RGB LEDs and detailed fault description on display
- Mute and soft function buttons................8 provided
- Standby Power button...........................On/Standby
- Meter button .......................................Toggles
through meter views
- Menu............................................. Provides a menu
driven interface for full function front panel control
- Rotary Encoder............................ Yes
- Exit Button................................... Provides
a “back” function
Power
- Operating voltage.................................. 140-265
V / 70-135 V 2
- Soft start / Inrush power .................... Yes
/ max. 5 A
- Power Average Limiter (PAL)................Yes
- Power Factor Correction (PFC)..............No
- Breaker Emulation Limiter (BEL) ............No
- Under Voltage Limiter (UVL).................... No
Dimensions
- Rack rail to rear panel..........................W:
483 mm (19”), H: 88 mm (2 U), D: 386 mm (15.2”)
Weight
- Weight .............................13.5 kg (30
lbs.)
Finish
- Finish............................Black painted
steel chassis with black painted steel / aluminum front
Approvals
- Approvals.......................... CE,
ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC
NOTES
1: Asymmetrical loading of the outputs will yield even
higher ratings. If one (or two) channel(s) has reduced power requirements, then
the voltage drop from the power supply will be reduced, resulting in higher
power availability for the other channel(s).
2: Separate 230 V or 115 V versions available. Not
selectable on the product.