The Teradek Bolt -730 Multicast Wireless Transmission
System is a latency-free wireless transmission system that sends 4:2:2, 1080p60
video at up to 300ft. This Bolt system comes in a set of 1 transmitter and
1 receiver.
The transmitter features a loop through SD/HD/3G-SDI output, so you
can transmit video, and send the output from the camera to a monitor or deck.
The transmitter features an internal battery, that can run the unit for up to
60 minutes, and it features 4-LED indicator lights that indicate battery level.
The Bolt system is suitable for exterior and interior
shoots, and it features Dynamic Frequency Selection that allows it adjust the
frequency bands it is using in real time to avoid interference. This Bolt Pro
comes with 1 receiver that feature 2 x SD/HD/3G-SDI outputs, however it can
also transmit to a Bolt receiver that features an HDMI output, allowing you to
take SDI in, transmit, and output via HDMI or SDI depending on the type of
receiver you are using. You can also mix and match SDI & HDMI receiver
units, up to a total of 4.
Features:
1 TX to Multiple RX :The Bolt system simultaneously transmits full 1080p60
video to up to 4 receivers.
Connectivity : The Bolt transmits uncompressed video using WSDI Pro, which
provides a wireless range of up to 300' (91.4m) and can co-exist with other
wireless equipment by dynamically adjusting the frequency bands used in real
time.
LED Indicators : The transmitter and receiver each feature LED indicators for
Video signal, and Link. The transmitter also features 4 LEDS that indicate
internal battery strength. On the side of the transmitter are additional LEDS
that indicate battery charge, DC power in, and Video Signal. The receiver
features Video, Link, and Ready LED indicators.
Rugged & Low Power : Bolt transmitters are housed in a 7 oz milled aluminum
chassis with six 1/4"-20 mounting holes. The receiver is enclosed in a
durable ABS plastic shell. The transmitter requires approximately 4W of power,
while the receiver consumes only 6W. To power these units for long periods of
time, a Lemo to P-tap cable (included) can be used to connect with external
power sources such as V-mount or AB Gold-mount batteries.
Bolt Pro's internal Li-Ion battery provides up to 60 minutes
of run time and can be charged via its micro USB port or its LEMO DC input.
Bolt Meets Cube
Connecting a Cube encoder to Bolt's 3G-SDI loop or receiver
output can result in powerful new workflows. This feature lets you to take
advantage of Bolt's latency-free monitoring capabilities, while simultaneously
sending Cube's compressed video feed to an iOS device, directly to the Web, or
to a decoder located offsite. The best part is that Cube and Bolt do not
interfere with one another so video dropouts will never be a problem.
What's in the Box?
Bolt Transmitter
Bolt Receiver
10" Coiled SDI Cable for Transmitter (25.4 cm)
Lemo to P-Tap Cable (6 to 28V)
1/4"-20 Thumbscrew
2-Pin Lemo to 18W AC Power Adapter
Pelican 1400 Case with Teradek Plate
Foam Bottom Insert for Bolt & Pelican
Foam Top Insert for Bolt & Pelican
Pelican Case 1400 Sticker Membrane
Specifications:
Transmitter
Input : SD/HD/3G-SDI
Output : Looping 3G-SDI
Resolution :Up
to 1080p60
Wireless Range: 300.0'
(91.4 m)
Power : 4.5 W
Battery: Re-chargeable
Li-Ion battery with 60 minutes run time
Cable : Lemo 6 to 28
VDC input (Pin 1 GND, Pin 2 +DC, 0B 302 series Lemo)
Encryption : AES128
Audio: 2-channel
Chassis: Milled
aluminum
Mounting: Multiple mounting options with 1/4"-20 holes