Overview:

Soavo-900SW Advanced YST II Front Firing Subwoofer

Advanced YST II

High Performance Driver

600W Digital Amplifier

Front Firing Design

Twin Wooden Linear Ports

Heavy-Duty Construction with Three-Way Mitered-Joint Construction

Birch Veneer Cabinet with Open-Pore Finish

Three BASS Modes

 

Full-Function Remote Control Unit

Three Preset Memories

Sleep Timer

Features:

Powerful, Accurate Sound

Cabinet

Convenient Features

Other Notable Features

Front Panel Features:

1. Remote control sensor - Receives signals from the remote control.

2. STANDBY/ON indicator - Green: Lights up when this unit is on. / Red: Lights up when this unit is in the standby mode. / Orange: Lights up when the sleep timer is on.

3.PHASE indicator - Green: Lights up when the phase is set in the reverse mode. / Red: Lights up when the phase is set in the regular mode.

4. STANDBY/ON switch - Turns on or sets this unit to the standby mode. In the standby mode, this unit consumes a small amount of power.

5. H-CUT control - Adjusts the high frequency cut off point depending on the connected front speakers or your preference

6.VOLUME control - Adjusts the volume level. Turn the control clockwise to increase the volume, counterclockwise to decrease the volume.

7. B.A.S.S. indicators - Light up to indicate the currently selected B.A.S.S. number (1, 2 or 3)

8. PRESET indicators - Light up to indicate the currently selected PRESET number (1, 2 or 3

Rear Panel Features:


1.GND Terminal

2. INPUT 3 Terminals

3.INPUT 2 (LFE) Terminals

4. OUTPUT Terminals

5.INPUT 1 Terminals

6. AC IN

7. POWER Switch

Remote Control Features:

1. STANDBY  - Sets this unit to the standby mode. In the standby mode, this unit consumes a small amount of power.

2. POWER - Turns on this unit

3 .B.A.S.S. - Selects a mode that is suitable for the source.Each time you press B.A.S.S., the B.A.S.S. indicator changes between 1, 2, and 3.

4. PRESET - Stores or recalls the B.A.S.S., volume, high-cut frequency  and phase settings

5. HIGH CUT - Adjusts the high frequency cut off point depending on the  connected front speakers or your preference

6. SLEEP - Sets the sleep timer

7. PHASE - Switches the phase mode.Normally, set this unit to the reverse position. However,  according to your speaker systems or the listening condition, there may be cases when better sound quality is obtained by setting this switch to the normal position. Select the better position by monitoring the sound.

8. MEMORY- Stores the B.A.S.S., volume, high-cut frequency and phase  settings

9.VOLUME - Adjusts the volume of this unit.

When your amplifier has a one-channel subwoofer terminal

Connect the subwoofer (or low pass etc.) terminal of your amplifier to the INPUT 3 ( /MONO) terminal of this unit  using a commercially available mono pin cable.


When your amplifier has two-channel subwoofer terminals

Using one subwoofer

Connect the “L” side subwoofer terminal of your amplifier to the INPUT 3 ( /MONO) terminal of this unit and “R” side subwoofer terminal of your amplifier to the INPUT 3 ( ) terminal of this unit using a commercially available audio pin cable

Using two subwoofers

Connect the “R” side subwoofer terminal of your amplifier to the INPUT 3 ( ) terminal on this unit using a commercially available mono pin cable, and connect the “L” side subwoofer terminal of your amplifier to the INPUT 3 ( /MONO) terminal of this unit using a commercially available mono pin cable

When your amplifier has one set of front speaker terminals

  • Connect the speaker terminals of the amplifier to the INPUT 1 terminals of this unit, and connect the OUTPUT terminals of this unit to the front speakers using a commercially available speaker cable.

When your amplifier has two sets of front speaker terminals and both terminals can output sound signals simultaneously

Connect one set of front speaker terminals of the amplifier to the INPUT 1 terminals of this unit, and connect another set of front speaker terminals of the amplifier to the front speakers using commercially available speaker cables.Set the amplifier so that both sets of front speaker terminals output sound signals simultaneously.

Specifications:

  • Type .... Advanced Yamaha Active Servo Technology II
  • Driver ...................................... 25 cm (10”) cone woofer Magnetic shielding type
  • Amplifier Output (100 Hz, 4 ohms, 10% T.H.D).......................... 600 W
  • Frequency Response ............................. 18 Hz - 160 Hz

Power Supply

  • U.S.A. and Canada models ............. AC 120 V, 60 Hz
  • U.K. and Europe models ................ AC 230 V, 50 Hz
  • Australia model .............................. AC 240 V, 50 Hz
  • Asia and General models......... AC 110/120/220/230-240 V, 50/60 Hz
  • Korea model ................................... AC 220 V, 60 Hz
  • China model ................................... AC 220 V, 50 Hz
  • Power Consumption ........................................... 180 W
  • Standby Power Consumption ............................. 0.5 W
  • Dimensions (W x H x D)........................ 410 mm x 457 mm x 462 mm / (16-1/8” x 17” x 18-3/16”)
  • Weight ............................................. 32 kg (70 lbs. 9 oz.)
  • Color...........................................Black

Note: Please note that all specifications are subject to change  without notice.