1. Browser Knob – Rotate the knob to cycle through foldersand tracks. When a folder is selected, press the knob to enter it. (Press BACKto move up to the previous level.)

2. Load – Press one of these buttons while a track isselected to assign it to Deck 1 or 2, respectively, in the software.

3. Back – Cycles between the file structure and the musiclibrary in the software.

4. Shift – Allows multiple control commands to be triggeredwhen pressed and held first along with other buttons.

5. Play/Pause – Starts and suspends playback.

6. Headphone Cue – Sends pre-fader audio to the Cue Channelfor headphone monitoring through your computer.

7. Cue (Transport Control) – Sets and recalls the main Cuepoint in the current track. Hold down the CUE button for temporary play of thecue point. The track will play for as long as the button is held down andreturn to the cue point once it is released.

8. Platter/Jog Wheel – This capacitive, touch-sensitive jogwheel controls the audio when the wheel is touched and moved. When the Scratchbutton is not active, use the wheel to bend the pitch of the track. When the Scratchbutton is active, use the wheel to grab and move the audio,"scratching" the track as you would with a vinyl record. You can alsograb the non-touch-sensitive outer wheel to bend the pitch of the track.

9. Scratch – Controls the behavior of the platters. When notactive, the platter will function as Pitch Bend. When active, the platter willhave the ability to scratch.

10. Pitch Fader – Controls the tempo (speed) of theindividual decks.

11. Pitch Bend - – Press and hold to momentarily reduce thespeed of the track.

12. Pitch Bend + – Press and hold to momentarily increasethe speed of the track.

13. Sync – Enables BPM syncing between decks for thesoftware tracks. To manually adjust BPM and exit Sync mode move the pitch faderof the deck you wish to adjust.

14. Effect Control – Adjusts the effect parameter in thesoftware of the last activated effect. Hold Shift + FX Control to select theeffect.

15. Filter – This knob will adjust the amount of Filter.Turning the knob left and right will produce a Low Pass Filter or High PassFilter.

16. Loop In – Press this pad to set the beginning of a loopwhen in Looping Mode. After a Loop Out point is set and this button is pressedagain, it will return the playback marker to the Loop In point. Pressing Shift+ Loop  In will set the current Pad Modeas “Looping Mode”. See the PAD MODE COMMANDS section for information on thispad’s additional functions.

17. Loop Out – Press this pad to set the end of a loop whenin Looping Mode. When this button is pressed again after a Loop Out point hasbeen set, it will exit out of the loop. Pressing Shift + Loop Out will set thecurrent pad mode to “Sample (S)” Mode. See the PAD MODE COMMANDS section forinformation on this pad’s additional functions.

18. Reloop – When this is pressed inside a Loop, this willturn the loop off. If a loop has not been set, this button will create a loopfrom the start of the song or where Loop In was pressed. Pressing Shift +Reloop will set the current pad mode to “Hot Cue Mode”. See the PAD MODECOMMANDS section for information on this pad’s additional functions.

19. Loop x1/2 – Press this pad to reduce the currentlyplaying loop length by half when in Looping Mode. If a loop is not playing,this will set the autoloop length. Hold Shift + Loop 1/2 to double the looplength. See the PAD MODE COMMANDS section for information on this pad’sadditional functions.

 20. FX 1 On/Off –Turns FX 1 on and off per deck. Hold Shift + FX 1 to set and start playback ofa 1-beat autoloop.

21. FX 2 On/Off – Turns FX 2 on and off per deck. Hold Shift+ FX 2 to set and start playback of a 2-beat autoloop.

22. FX 3 On/Off – Turns FX 3 on and off per deck. Hold Shift+ FX 3 to set and start playback of a 4-beat autoloop.

23. Reset – Press this pad to reset the filter. Hold Shift +Reset to set and start playback of a 16-beat autoloop.

24. Channel Volume – Adjusts the volume of the individualchannels in the software.

25. Master Volume – Adjusts the volume of the master mixcoming from the software.

26. Crossfader – Controls the blend between the two decks.

27. High EQ – Controls the treble frequencies for theindividual channels.

28. Mid EQ – Controls the mid range frequencies for theindividual channels.

29. Low EQ – Controls the bass frequencies for theindividual channels.

30. Cue Gain – Adjusts the volume for headphone cueing inthe software.

31. Cue Mix – Adjusts the software’s audio output to theheadphones, mixing between the cue output and the master mix output.

32. Stutter – Press this button while the music is playingto jump back to the last set cue point, creating a "stutter"  effect.